Rafter tail repair
Rotted rafter ends behind the fascia are sistered or rebuilt so the new board stays put.
Exterior Services
Fascia Repair Paramus, NJ
A Paramus roofer can repair the fascia boards that carry your gutters and cap the ends of the rafters, once the source of the water is found. Dial (551) 383-2304 to talk with a local roofer about the fascia.
Fascia rot nearly always comes from water getting behind the gutter. Clogged or poorly pitched gutters spill over the back, and a roof edge with no drip edge sends water straight down the fascia. Over a few seasons the wood softens, the gutter screws lose their grip and the gutter starts to sag or pull away.
What starts as a soft board can spread well past the trim. Left alone, the rot moves into the rafter ends and the edge of the roof deck, which turns a trim repair into structural work. Metal-wrapped fascia is especially tricky because water can get trapped behind the wrap and rot the wood out of sight.
Before the visit, take a look along the roof edge from the ground. Write down which sides of the house show peeling paint, gaps or a sagging gutter. It also helps to know the fascia material and whether the gutters are original to the house.
Fascia Repair is often paired with soffit repair and gutter installation, depending on the cause.
Looking for Paramus fascia repair? Call (551) 383-2304 to reach a nearby roofing contractor.
Call nowThe process
How fascia repair works
Good fascia work deals with the roof edge, the gutter and the board together.
Check the edge
The roofer checks the drip edge, the first course of shingles, the gutter pitch and the downspouts above the damaged fascia. An awl or screwdriver finds the edges of the soft wood.
Remove the gutter
The gutter section over the damage is unhooked and set aside so the fascia can come off. Old spikes and loose hangers are not reused.
Repair the framing
With the fascia off, the rafter ends and the edge of the roof decking are checked for rot. New fascia nailed to rotten rafter ends will loosen again.
Install new fascia
A replacement board matched to the existing size goes up, sealed at the ends and joints. End grain is sealed so it does not soak up water.
Fix the edge flashing
The metal drip edge at the roof edge is adjusted so runoff lands in the gutter, not behind it. This is the piece that keeps the new fascia dry.
Rehang the gutter
The gutter goes back up with new hidden hangers screwed into solid wood, pitched toward the downspout. The finished edge is checked with a hose or after the next rain.
What is included
Fascia repairs a roofer can handle
Drip edge installation
Missing or bent drip edge is replaced at the roof edge which stops the rot from coming back.
Soft fascia
Soft wood along the roof edge is removed back to sound material with sealed joints and ends.
Gutter rehanging
Sagging gutters are rehung on solid fascia with new hangers at the right slope.
Aluminum wrap
Metal wrap can be added over new or sound fascia to cut down on painting.
Related service
Fascia Board Replacement Paramus, NJ
When rot runs along most of a wall, or the boards are split and warped end to end, replacing the full run of fascia is the cleaner fix. The gutters come down, the old boards come off and the rafter tails behind them are checked before new boards go up. Many homeowners switch to PVC or composite fascia at this point because it will not rot.
In Paramus, fascia board replacement often lines up with a new roof or new gutters, since the roof edge is already being worked on. Be wary of any plan that covers rotted boards with metal instead of replacing them. The new boards should match the old width so the soffit closes properly.
Related service
Fascia Board Repair Paramus, NJ
When rot is confined to short stretches, the damaged part of the board can be cut out and a new piece scarfed in. The new piece is joined with an angled scarf joint so the seam is strong and less likely to open. Minor surface damage may only need consolidant, filler and paint.
A fascia board repair in Paramus should always include a look at why that spot got wet. That usually means resealing a gutter seam, unclogging a downspout or adding drip edge over the repaired section. Once the wood is primed and painted on all sides, a repaired section can last as long as the rest of the board.
Local help
Fascia Repair Near Me
In Paramus, fascia tends to fail first on the sides of the house where gutters clog fastest. From Paramus out to neighboring towns such as Oradell, River Edge, Fair Lawn and New Milford, older roof edges often need board and rafter tail repair while newer ones more often need drip edge and gutter fixes, which is why keeping gutters clear does so much to protect the fascia.
For fascia repair in Paramus, NJ or nearby towns like Oradell, River Edge, Fair Lawn and New Milford, call (551) 383-2304 to reach a roofer who covers your street.
How the weather here affects roofs around Paramus
Cold winters bring snow, ice and a long stretch of freezing nights. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, building ice dams that push water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. That is why roof repair in Paramus is busiest after a hard winter and before the next one.
Why call
Why not wait
Smaller repairs
Small roof problems caught early usually stay small repairs.
Local knowledge
Local roofers see the same roofs and storm damage across Paramus and nearby towns.
Know what happens next
Ask your questions before you agree to anything.
Common questions about fascia repair
Should I cover rotted fascia with metal?
Covering rotted wood with aluminum hides the rot instead of stopping it. Gutter screws go through the wrap into the rotting board and gradually pull loose. Wrap is a good finish over new or solid fascia.
What causes fascia boards to rot?
Water getting behind the gutter is the main cause. Clogs, bad seams and the lack of a drip edge are the usual culprits. Peeling paint and unsealed cut ends speed up the damage.
Can fascia be repaired instead of replaced?
Spot repairs work well for rotted corners and short stretches. When rot runs along most of a wall or the boards are split throughout, full replacement makes more sense. Either way, the rafter tails behind the board need to be checked.
What is the best material for fascia?
PVC and composite fascia resist rot and hold paint well. Wood is common on older homes and works well when kept painted. Whatever you choose, a proper drip edge and working gutters matter more than the board itself.
Do fascia boards affect my gutters?
The fascia is what gutters are fastened to. Soft fascia lets the fasteners work loose, which is often the first sign of rot. The fix is solid wood plus new hangers, pitched toward the downspout.
More questions? Call (551) 383-2304
Other services that may help
Soffit Repair
Repairs for rotted, sagging or loose soffit panels under the roof eaves, so the attic breathes and the overhang stays sealed.
Learn moreGutter Installation
New gutters and downspouts formed to fit the house, with the right size, pitch and outlet placement, from K-style aluminum to half-round and copper.
Learn moreGutter Repair
Fixing gutters that drip at the corners, sag between hangers or pull away from the fascia, so roof water drains where it should again.
Learn moreRoof Repair
Fixing the shingles, flashing, boots and decking that let a roof down, without replacing a roof that still has life left.
Learn more
Looking for something else?
See all roofing servicesNeed fascia repair in Paramus, NJ?
Call (551) 383-2304 for a local roofer in Paramus and nearby towns.