Coating
An aged but sound roof can be primed and coated once all leaks are fixed.
Flat Roofing
Rubber Roof Repair Paramus, NJ
Most leaking rubber roofs in Paramus can be repaired, since EPDM patches bond well when the surface is cleaned and primed properly, once the actual leak point is located. One call to (551) 383-2304 reaches a nearby rubber roof repair pro.
Rubber roofs fail in a few predictable places. The seams fail first on many older rubber roofs, because the original seam adhesive loses its grip after years of sun. Next come punctures from foot traffic, branches or dropped tools, and flashing that tears where the membrane meets walls, curbs and pipes.
Over time, EPDM slowly shrinks, and that causes its own kind of damage. Shrinking rubber pulls tight at the perimeter, tenting across corners and tearing at flashing seams. The fix is releasing the tension and adding new flashing, not just caulking the gap.
Avoid one common shortcut before the roofer arrives. Asphalt roof cement, tar and many general purpose sealants contain solvents that soften and swell EPDM, and nothing made for rubber will bond over them later. Instead, catch drips inside, stay off the roof when it is wet and note where stains appear.
Rubber Roof Repair is often paired with rubber roof installation and flat roof repair, depending on the cause.
Looking for Paramus rubber roof repair? Call (551) 383-2304 to reach a nearby roofing contractor.
Call nowThe process
What happens during a rubber roof repair
EPDM repairs depend on surface preparation more than anything else.
Locate the source
Seams, perimeter flashing and penetrations are checked first, since that is where most rubber roofs leak. The roofer also checks whether water has soaked the insulation underneath.
Prepare the surface
The repair area is cleaned thoroughly, because dirt and chalky residue keep patches from bonding. Any old tar or asphalt patch is removed first.
Prime the area
A rubber primer is applied and given time to dry to the touch. This step is what lets the patch bond chemically to aged rubber.
Apply the patch
Peel-and-stick EPDM cover tape or a cured patch is cut with rounded corners, pressed down and rolled firmly with a seam roller. Corners and penetrations use flexible uncured flashing.
Reseal the seams
Open seams are cleaned, primed and covered with seam tape or a cover strip along their full length. Lap sealant protects the edges.
Wall flashing
Where the rubber has pulled away, the roofer relieves the tension, adds new flashing up the wall and secures it with termination bar. The top of the flashing is fastened and sealed.
What is included
Common EPDM repairs
Seam repair
Open laps are resealed with seam tape with lap sealant at the edges.
Pipe boots
Damaged collars around penetrations are renewed with pre-molded boots or uncured flashing.
Tear repair
Damaged rubber is covered with new membrane rolled for a full bond.
Shrinkage repair
Stretched corners are cut free and patched with termination bar where needed.
Related service
EPDM Roof Repair Paramus, NJ
Every EPDM repair depends on the same steps, done in order. The rubber must be clean and dry, the primer must be scrubbed in and allowed to flash off and the patch must be rolled firmly so it bonds across its whole surface. A bead of lap sealant seals the patch edges.
In Paramus, rubber roof repairs are best done on dry days when the membrane is not too cold. Short-term fixes can protect the house until the weather cooperates. Temporary seals are not a substitute for a primed patch.
Related service
Rubber Roof Replacement Paramus, NJ
There comes a point where patching an EPDM roof stops being worth it. Seams failing all over, shrinkage pulling at every wall, a brittle and crazed surface or wet insulation across large areas all point toward a new roof. A moisture survey helps decide.
Some owners stay with EPDM, while others move to a white membrane. If the existing roof is a single layer with dry insulation, a recover may be possible, but wet insulation means a tear-off. Ask the Paramus roofer to compare repair and replacement for your roof.
Local help
Rubber Roof Repair Near Me
Rubber roofs in Paramus cover many porch roofs, additions, garages and flat sections on older homes. Homes in Paramus and nearby places including Oradell, River Edge, Fair Lawn and New Milford get the most from an EPDM roof when seams and flashing are checked every year or two, so a check after big storms is worth it.
For rubber roof repair in Paramus, NJ or nearby towns like Oradell, River Edge, Fair Lawn and New Milford, call (551) 383-2304 to reach a roofer who covers your street.
How the weather here affects roofs around Paramus
Cold winters bring snow, ice and a long stretch of freezing nights. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, which is how ice dams form and back water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. Most homeowners in Paramus, NJ have the roof checked in the fall and again after the snow melts.
Why call
Why act early
Drier ceilings
A roof problem fixed early rarely spreads to the decking, the insulation or the ceilings.
Familiar with local homes
Local roofers see the same roofs and storm damage across Paramus and nearby towns.
Know what happens next
Ask the roofer about the cause, the options and the estimate before work starts.
Common questions about rubber roof repair
What causes EPDM to pull away from the edges?
Aging rubber contracts over time. As it shrinks, it pulls on the flashing, stretches across inside corners and can tear at the wall. Repairs release the strain and reflash the wall.
What is the right way to patch EPDM?
A proper EPDM patch is a cleaned, primed and rolled repair. The roofer scrubs the area with membrane cleaner, applies primer, lets it flash off, then presses down a patch with rounded corners and rolls it firmly. Lap sealant finishes the edges.
Is roof cement safe for an EPDM roof?
Asphalt-based products damage rubber roofing. Their solvents soften and swell the rubber, and they leave a surface that proper EPDM patches cannot bond to. A proper repair uses rubber-specific primer and tape.
Should I coat my EPDM roof?
Coating is an option for a sound EPDM roof. Seams and leaks must be fixed, and the right primer is essential. Wet insulation has to be replaced first.
How long does a rubber roof last?
EPDM can last 20 years or more, sometimes much longer. Thicker membranes, good seams and regular inspections push it toward the longer end. Repairs keep it on track.
More questions? Call (551) 383-2304
Often needed together
Rubber Roof Installation
EPDM rubber roof installation with the right thickness, attachment method and flashing details, so the roof stays flexible and watertight for decades.
Learn moreFlat Roof Repair
Flat roof repairs matched to the membrane, whether EPDM, TPO, PVC, modified bitumen or built-up, with the patch made from material that bonds to what is there.
Learn moreRoof Coating
Silicone, acrylic and other liquid coatings that renew aging flat, low-slope and metal roofs, when the roof underneath is still dry and solid.
Learn moreRoof Leak Repair
Stopping water at the pipe boots, flashing, valleys and nail holes where roofs actually leak, before wet decking and insulation turn into rot.
Learn more
Looking for something else?
See all roofing servicesGet rubber roof repair help in Paramus
Call now for Paramus rubber roof repair and help in the towns around it.